AMIG-280PM
×

AMIG-280PM

  • Full digital multi-core MCU + DSP control
  • Multi-process: MIG/ PULSE MIG/DOUBLE PULSE/LIFT TIG/ MMA 
  • The built-in expert database program enables it performing carbon steel, stainless steel, aluminum and other materials welding; solid core wire and flux-cored gas shielded welding wire are applicable; the minimum thickness of aluminum sheet to weld is 0.7mm
  • The gas pre-flow time, gas post-flow time, slow wire feeding speed and burn back time are adjustable in MIG mode; double-pulse parameters are adjustable
  • 2T/4T/SP-4T/SPOT welding mode selection; synergic adjustment
  • One-key to save and recall 100 sets of parameters intelligently
  • VRD function
  • Intelligent fan control; ECO design
  • Full-bridge inverter, double IGBT modules, quick recovery diode module;
  • PCB is processed with three-proofing lacquer 
  • It enjoys IP21S class protection and H class insulation
  • Protection against overheat, over-current, over-voltage, short circuit, the faults of wire feeder and others; error code display
  • 3-phase power supply; small size and light weight (29Kg); light industries; 
  • Built-in wire feeding mechanism, the diameter of wire spool can reach up to 300mm
  • 4-roller drive + encoder feedback ensure stable and robust wire feeding
  • European type wire pushing welding torch

AMIG280PM
Rated input voltage/frequency (Hz)3 phase, 380V±10%, 50Hz
Rated input capacity (KVA)14.3
Rated input current (A)21.5
Duty cycle (40̊C)40%@280A
OCV (V)107
VRD (V)16
Output current range (A)20-280
Output voltage range (V)15-28
Wire size (mm)0.8,1.0,1.2
Protection classIP21S
Dimension (mm)630*280*480
Weight (kg /lb)34/74.8
  • 1 Power source
  • 1 Connected primary cables L=3m
  • 1 Ground cable L=3m
  • 1 Gas cooled torch L=3m
ASAW-II-630/1000/1250/1500
×

ASAW-II-630/1000/1250/1500

  • Cladding for CS/SS/wear-resistant plate
  • High-power plate welding: weld plate thicker than 3mm
  • Single wire and twin-wire single arc SAW, electroslag welding and strip cladding processes
  • SMAW and GOUGING processes
  • 3-phase power supply
  • Tractor enjoys digital communication control; thick wire (3.0-6.0) welding tractor, thin wire (1.6-2.4) welding tractor, fillet welding tractor, three-wheeled tractor and pipeline welding tractor can be applied
  • The control design to prevent tractor from tipping over (protection against welding wire short-circuiting with workpiece)
  • Tractor control box enjoys a storage of 10 sets of parameters
  • CC & CV characteristics; wire diameter can be selected (φ1.6-φ6.0)
  • SAW process: arc starting current, arc starting time, slow wire feeding speed, arc stopping current, arc stopping voltage, arc stopping time and burn back time are adjustable
  • SMAW process: arc force is adjustable
  • Intelligent fan control technology; Eco design;
  • Duty cycle (40℃): 100%
  • Efficiency reaches up to 89% 
  • Full-bridge inverter soft switch control technology, twin parallel inverter circuits, 4 IGBT modules, quick recovery diode module; long-life polypropylene filter capacitor
  • PCB is processed with three-proofing lacquer; the drive board is processed with rubber for protection
  • It enjoys IP21S class protection and H class insulation
  • Protection against overheat, over-current, over-voltage, output short-circuiting and others; error code display

ASAW630 IIASAW1000 IIASAW1250 IIASAW1500 II
Rated input voltage/frequency (Hz)3 phase, 380V±10%, 50 /60Hz
Rated input capacity (KVA)33.65575.785.6
Rated input current (A)5183115130
Duty cycle (40̊C)100%@630A100%@1000A100%@1250A60%@1500A
OCV (V)89849292
Adjustable current range (A)60-63060-100060-125060-1500
Adjustable voltage range (V)22-44
Wire size (mm)1.6-3.03.0-6.0
Protection classIP21S
Insulation classH
Dimension (mm)708*336*584788*366*815788*366*846788*366*846
Weight (kg /lb)55 /110.495 /209.8100 /220.9105 /232
  • 1 Power source
  • 1 Connected primary cables L=3m
  • 1 Ground cable L=5m
  • 1 Welding cable L=15m
  • 1 Control cable L=16m
  • 1 Tractor
ATIG210PAC
×

ATIG210PAC

  • Single phase, AC 220/230V power supply, small size and light weight (11.5Kg); powered by generator
  • APFC power factor correcting technology, small input current (16A), suitable for family application
  • Multi-process, 7 in 1: AC TIG/AC PULSE TIG/AC MIXER TIG/DC TIG/DC PULSE TIG/AC MMA/DC MMA
  • High frequency start [HF TIG] and lift start [Lift TIG]
  • All TIG parameters are adjustable (pre-gas/post-gas, up-slope/down-slope, AC frequency/clean ratio, peak/base current, duty cycle/frequency, arc starting/stopping), digital display
  • 2-T, 4-T, repeat and spot welding functions
  • Save and recall 10 sets of parameters
  • Remote control function; it can be applied matching with automation equipment, digital welding torch, analog welding torch and foot pedal 
  • Adjustable hot arc starting current, hot arc starting time and arc force in MMA mode realize effects of easy arc starting, anti stick and stable arc
  • Anti stick function
  • The switch of VRD function: low OCV (13V) ensures safety, high OCV ensures arc starting successful rate
  • Duty cycle: 200A@30%@40℃ (TIG)
  • Full-bridge IGBT inverter technology, secondary inverter technology; super big aluminum radiator ensures good heat dissipation
  • PCB is processed with three-proofing lacquer
  • It enjoys IP21S class protection and F class insulation
  • Protection against overheat, over-current, over-voltage, fan short-circuiting, and welding torch short-circuiting; error code display

ATIG210PAC
Rated input voltage/frequency (Hz)1 phase, 230V±10%, 50 /60Hz
Rated input capacity (KVA)5.7
Rated input current (A)25
Duty cycle (40̊C)35%@210A
OCV (V)60
MMAOutput current range (A)10-170
Arc force (A)0-100
Hot start (A)0-100
TIGOutput current (A)3-210
Pre-gas /post-gas (s)0.1-9.99 /0.1-60
Initial /final current (A)3-210 /3-210
Up-slope /down-slope time (s)0-10 /0-15
Peak current (A)3-210
Base current (A)3-210
Pulse frequency (Hz)DC: 0.2-500/ AC: 0.2-20
Pulse duty cycle5-95%
AC frequency (Hz)10-250
AC balance-40%±40%
Trigger mode2 /4T, Spot, Repeat
Arc ignition methodHF /Lift
Protection classIP23S
Insulation classF
Dimension (mm)430*160*300
Weight (kg /lb)11.5 /25.2
  • 1 Power source
  • 1 Connected primary cable L=3m
  • 1 TIG torch (with accessories)
  • 1 Ground cable L=3m with clamp and quick plug
  • 1 Quick plug
ATIG-P-270
×

ATIG-P-270

  • Light weight (19kg), small size; 
  • It can perform both manual cellulose electrode (CEL) root welding and TIG welding process, which meets requirements of field construction.
  • High frequency start [HF TIG] and lift start [Lift TIG]
  • Adjustable TIG parameters (pre-gas/post-gas, up-slope/down-slope, arc starting/stopping, peak/base current, duty cycle/ frequency); digital display
  • 2T/4T, repeat and spot welding operation mode
  • Gas-test function 
  • Pulse frequency can reach up to 500Hz, which enjoys more focused arc and deeper welding penetration
  • Adjustable hot arc starting current and hot arc starting time in MMA mode provide easy arc starting and high arc starting successful rate 
  • Adjustable arc force in MMA mode realizes effects of unbroken arc, anti stick and stable arc
  • Suitable for BAS & RUT & CEL welding
  • VRD function
  • Remote control: wired control, foot pedal, digital welding torch;
  • Intelligent fan control (Fan on demand)
  • Full-bridge inverter soft switch control technology, double IGBT modules, quick recovery diode module; long-service polypropylene filter capacitor
  • PCB is processed with three-proofing lacquer; the drive board is processed with rubber for protection
  • It enjoys IP23S class protection and H class insulation
  • Protection against overheat, over-current, over-voltage, short circuit, welding torch switch short-circuiting; error code display
  • 3-phase power supply, generator powering design;

ATIG270P

Rated input voltage/frequency (Hz)3 phase, 380V±10%, 50 /60Hz
Rated input capacity (KVA)10
Rated input current (A)16.5
Duty cycle (40̊C)35%@275A  100%@200A
OCV (V)(MMA /TIG)MMA(23V) /TIG(77V)
MMAOutput current (A)5-275
Arc force (A)10-200
Hot start (A)20-160
TIGOutput current (A)5-275
Pre-gas /post gas (s)0.1-9.99/0.1-60
Initial /final current (A)5-275/5-275
Up-slope /down-slope (s)0.1-10 /0.1-20
Peak current (A)5-275
Base current (A)5-275
Pulse frequency (Hz)0.2-30 /30-500
Pulse duty cycle10%-90%
Trigger mode2T, 4T, Spot welding, Repeat
Arc ignition methodHF
Protection classIP23S
Insulation classH
Dimension (mm)460*210*410
Weight (kg /lb)19 /42
  • 1 Power source
  • 1 Connected primary cable L=3m
  • 1 Welding cable L=3m
  • 1 Ground cable L=3m
  • 1 TIG torch
AMIG-500PS
×

AMIG-500PS

  • Full digital multi-core MCU + DSP control
  • 3-phase power supply; optional generator powering
  • Closed or open type wire feeding mechanism, the 15kg wire spool can be applied
  • 4-roller drive + encoder feedback provide stable and robust wire feeding; analog wire feeder
  • European wire pushing welding torch
  • Flux-cored welding wire / solid wire
  • Built-in expert database program enable it directly performing carbon steel, stainless steel and other materials welding
  • Wire diameter can be selected
  • Gas pre-flow time, gas post-flow time, burn back time and spot welding time are adjustable
  • 2T/4T/ spot welding operation mode; synergic/ separate adjustment
  • One-key to save and recall 10 sets of parameters intelligently
  • Gas test function; wire test function; digital display
  • Intelligent fan control technology; Eco design
  • Efficiency reaches up to 89%
  • Full-bridge inverter soft switch control technology, double IGBT modules, quick recovery diode module; 
  • PCB is processed with three-proofing lacquer; the drive board is processed with waterproof rubber
  • It enjoys IP21S class protection and H class insulation
  • Protection against overheat, over-current, over-voltage and output short-circuiting; error code display

AMIG500PS
Rated input voltage/frequency (Hz)3 phase, 380V±10%, 50 /60Hz
Rated input capacity (KVA)24
Rated input current (A)38
Duty cycle (40C)60%@500A
OCV(V)101
Output voltage range (V)60-500
Output current range (A)10-50
Protection classIP23
Insulation classH
Dimension (mm)640*320*590
Weight (kg /lb)50/110
  • 1 Power source
  • 1 Connected primary cable L=3m
  • 1 Ground cable L=3m
  • 1 Water-cooled torch L=3m
  • 1 Wire feeder with Europe connection
  • 1 Water cooling machine
  • 1 Trolley
AMIG-500/630PD
×

AMIG-500/630PD

  • Full digital multi-core MCU + DSP control
  • Deep penetration carbon steel welding process realizes full penetration welding for medium thick plate and one-time penetration welding for 12mm thick plate with no groove. It enjoys 30% deeper welding penetration than standard pulse MIG for which the welding quality is outstanding. Thick plate welding enjoys reduced groove angle and material cost. It also enjoys lower labor cost through reducing the number of welding layers and passes.
  • Built-in expert database program enables it performing carbon steel, stainless steel, aluminum and other materials welding; solid core wire and flux-cored gas shielded wire are applicable.
  • Optional wire diameter: 1.0/1.2/1.4/1.6/D 1.0/D 0.8;
  • Gas pre-flow time, gas post-flow time, burn back time, slow wire feeding speed, spot welding time, double-pulse and deep penetration parameters are adjustable
  • 2T /4T /SP-4T /spot welding operation modes
  • One-key to save and recall 100 sets of parameters intelligently
  • Intelligent fan control technology; Eco design;
  • Efficiency reaches up to 89%
  • Full-bridge inverter soft switch control technology, double IGBT modules, quick recovery diode module  
  • PCB is processed with three-proofing lacquer and the drive board is processed with waterproof rubber
  • It enjoys IP23 class protection and H class insulation
  • Protection against overheat, over-current, over-voltage, output short-circuiting and the faults of wire feeder; error code display
  • Closed type wire feeder and the 15kg wire spool is applicable; 4-roller drive + encoder feedback ensure stable and robust wire feeding; digital and analog wire feeder can be selected
  • European type wire pushing welding torch, digital welding torch and push-pull welding torch can be selected
  • 3-phase power supply; optional generator powering

AMIG500PDAMIG630PD
Rated input voltage/frequency (Hz)3 phase, 380V±10%, 50 /60Hz
Rated input capacity (KVA)2434
Rated input current (A)3851
Duty cycle (40̊C)100%@500A100%@630A
OCV (V)10698
Adjustable current range (A)60-50060-630
Adjustable voltage range (V)17-3917-44
Trigger mode2 /4T, Spot, Special 4T /Special 2T
Wire size (mm)1.0, 1.2, 1.4, 1.61.0, 1.2, 1.4, 1.6
Double pulse frequency (Hz)0.5-5
Job channels100
Protection classIP23
Dimension (mm)655*324*546655*324*546
Weight (kg /lb)55 /12165 /143
  • 1 Power source
  • 1 Connected primary cable L=3m
  • 1 Water cooling machine
  • 1 Ground cable L=3m
  • 1 Water-cooled (or Gas-cooled) torch L=3m
  • 1 Wire feeder with Europe connection
  • 1 Trolley
ASAW-1000IV
×

ASAW-1000IV

  • High-power plate welding: to weld plate thicker than 3 mm 
  • SAW processes: Single wire, twin-wire single arc, electroslag welding, strip cladding, visible arc cladding process;
  • SMAW and GOUGING processes
  • GMAW: single wire, twin-wire single arc GMAW processes [1.2/1.6]
  • Robotic SAW and GMAW processes
  • 3-phase power supply
  • Multi choices for tractor: thick-wire (3.0-5.0) welding tractor, thin-wire (1.6-2.4) welding tractor, fillet welding tractor, three-wheeled tractor and pipeline welding tractor are available
  • The control design to prevent tractor from tipping over (protection against welding wire short-circuiting with workpiece) 
  • The control box of tractor enjoys a storage of 10 sets of parameters;
  • Matching with automation equipment and robot: digital communication interfaces (485, CAN, CAN OPEN, DEVICENET, ETHERNETIP, ETHERCAT, PROFINET) and standard analog control interfaces make robot connection much convenient
  • CC&CV characteristics; wire diameters can be selected (1.2-5.0)
  • SAW process: arc starting current, arc starting time, slow wire feeding speed, arc stopping current, arc stopping voltage, arc stopping time and burn back time are adjustable 
  • GMAW process: gas pre-flow time, gas post-flow time, burn back time, slow wire feeding speed, spot welding time, ball removing voltage and ball removing time are adjustable
  • Intelligent fan control technology; Eco design
  • Duty cycle (40℃): 100%; efficiency reaches up to 89%
  • Full-bridge inverter soft switch control technology, twin parallel inverter circuits, 4 IGBT modules, quick recovery diode modules
  • PCB is processed with three-proofing lacquer; the drive board is processed with rubber for protection
  • It enjoys IP21S class protection and H class insulation
  • Protection against overheat, over-current, over-voltage and output short-circuiting; error code display

ASAW1000 IV
Rated input voltage/frequency (Hz)3 phase, 380V±10%, 50 /60Hz
Rated input capacity (KVA)55
Rated input current (A)83
Duty cycle (40̊C)100%@1000A
OCV (V)84
Adjustable current range (A)60-1000
Adjustable voltage range (V)14-50
Wire size (mm)1.2-6.0
Protection classIP21S
Insulation classH
Dimension (mm)788*366*815
Weight (kg /lb)95 /209.8
  • 1 Power source
  • 1 Connected primary cable L=3m
  • 1 Ground cable L=5m
  • 1 Welding cable L=15m
  • 1 Control cable L=16m
  • 1 Tractor
TANDEM-1000/1250
×

TANDEM-1000/1250

  • Effectively reduce the number of welding layers and passes, and inter-layer cleaning and other assistant time; the total efficiency can reach three times of single wire welding.
  • The super edge tool of low-cost thick plate welding, which can realize welding without back gouging and grooving for medium thick plate no thicker than 25mm. It enjoys a welding cost 60% lower than before.
  • Under the condition of same welding heat input, twin-wire SAW enjoys higher deposition rate and welding speed.
  • The DC arc of anterior wire ensures penetration and the AC arc of posterior wire improves welding seam formation. The separate parameters adjustment of two wires provides easy parameters presetting, so as to meet more technical requirements. 
  • It enjoys flexible configuration, which can be applied to form a tractor type tandem SAW system or a automatic tandem SAW system.
  • Two full digital inverter welding machines perform well in high efficiency and energy saving
  • The DC and AC welding machines can perform simultaneously or separately, so as to meet different welding requirements.

TANDEM1000TANDEM1250

ASAW1000IIASAW100-AC/DCASAW1250IIASAW1000-AC/DC
Rated input voltage/frequency (Hz)3 phase, 380V±10%, 50 /60Hz
Rated input capacity (KVA)5575.755
Rated input current (A)8311583
Duty cycle (40̊C)100%@1000A100%@1000A100%@1250A100%@1000A
OCV (V)89909290
Adjustable current range (A)60-100050-101060-125050-1010
Adjustable voltage range (V)22-44
Wire size (mm)3.0-6.0
Protection classIP21S
Insulation classH
Dimension (mm)788*366*8151040*500*720788*366*8461040*500*720
Weight (kg /lb)95 /209.8165 /364.7100/220.9165 /364.7
ACUT-300/400
×

ACUT-300/400

  • Best choice for thick plate cutting; Cutting carbon steel with maximum thickness of 110mm can be realized when the current is 400A; Quality cutting is accessible for the plate with maximum thickness of 80 mm; 
  • Cutting speed is greatly improved, which is 2 times that of 200A cutter; as for 25mm thick carbon steel, cutting speed can reach 2800mm/min. 
  • Outstanding cost control performance: High power inverter equipment saves 15-30% energy than SCR power source; Cost is cut by 10% because of high quality and long service life consumables. 
  • Twin-function setting: accessible to perform cutting and gouging 
  • It enjoys flexible configuration, which can perform manual cutting, also can be equipped with CNC to form an automatic cutting system; 
  • The refrigeration equipment of compressor ensures stable torch cutting.
  • Built-in air filtering and pressure reducing valve, the integration of air pressure digital display and adjustment function is on the panel
  • Non-contact high frequency start (transferred arc)
  • Full digital control; pre-gas, post-gas, up-slope time and down-slope time are continuously adjustable  
  • 2T/4T operation mode
  • The digital display of liquid flow 
  • Duty cycle (40℃): 100%
  • Full-bridge inverter soft switch control technology, twin-circuit inverter, 4 IGBT modules, quick recovery diode module; long-life polypropylene filter capacitor
  • PCB is processed with three-proofing lacquer; the drive board is processed with rubber for protection
  • It enjoys IP21S class protection and H class insulation
  • Protection against overheat, over-current, over-voltage, under-voltage, lack of coolant, lack of air pressure and short circuit; error code display
  • Long life consumables, low cost operation
ModelACUT300ACUT400
Primarypower voltage/frequency3 phase,AC380V/ 400V±10%,  /50Hz
Rated input power (KVA)7495
Rated input current (A)112142
Output current range (A)60-30060-400
Output voltage range (V)104-200
Rated duty cycle (%)100
Open circuit voltage (V)380
Efficiency (%)≥89%
Air pressure (bar)4.5-6
Air flow (L/min)≥250
 Maximum cutting thickness/CS (mm)100   110
  Cutting thickness in quality/CS (mm) ≥70≥80 
Dimensions (mm3)783×364×849
Weight (Kg)116 120 
IP class                                                                    IP21S                                                                 
 Insulation classH
Robot System
×

Robot System

  • Easy and flexible operating platform provides quick and easy switch of workpiece; the flexible platform and external axial are optional
  • Self-recovery at the temporary stop point: When abnormal gas flow, running out of wire and temporary stop occurs to the welding process, robot can automatically move to the stop point from any other position and continues welding after removing all failures after recalling the command of “continue last time welding”.
  • Torch cleaning and wire cutting functions (optional): Robot can automatically realize torch cleaning and wire cutting through program software so as to ensure good arc starting and precise welding seam locating.
  • Welding seam locating function(optional): Robot can automatically find the start position and final position of the welding seam when workpiece deformation or imprecise assembly occurring. It can also realize welding seam tracking and multi-layer multi-pass welding through cooperating with corresponding software.
  • Anti-collision function: The robotic welding torch can automatically travel back when colliding with any objects so as to protect welding torch and robot body.
  • Expert database: The system can automatically accomplish arranging welding passes and the adjusting corresponding welding parameters through setting the necessary welding conditions in the program.  
  • Teaching programming: It can realize programming through the teaching pendant equipped by robot in construction site.
  • Fault self-diagnoses: Welding machine and robot can judge all kinds of emergencies, and try to repair automatically. Relevant fault information is provided by displaying error code for the fault that cannot be repaired automatically. 
  • Welding torch oscillation: It ensures the beauty of welding pass during conducting fill and cosmetic welding through realizing flat oscillation and pendulum oscillation functions.